Guide :Freezers : Freezers

Ice maker leaks into the ice storage bin

Amanda ice maker in the freezer section leaks into the ice storage bin and causes big chunks of ice to build up and jams up the realease of ice cubes.

Research, Knowledge and Information :


Ice Block or Water Leaking in Icemaker Area | FAQ | Sub-Zero


Find answers online to your Sub-Zero & Wolf Appliance customer service questions here. Read about Ice Block or Water Leaking in Ice Maker Area.
Read More At : www.subzero-wolf.com...

The ice maker drips water into the ice bin. It flows from


The ice maker drips water into the ice bin. ... Your problem is too much water comes into the ice maker or is it leaking from the ice maker? Customer:
Read More At : www.justanswer.com...

Icemaker is dripping (leaking, repair, replace, plastic ...


Jul 02, 2012 · Icemaker is dripping (leaking ... into the hopper/storage bin, which ... you can take off the front of the ice-maker and a water level ...
Read More At : www.city-data.com...

Troubleshooting an Ice Maker that Leaks | DoItYourself.com


Troubleshooting an Ice Maker that Leaks Troubleshooting an Ice Maker that Leaks. When ... When water enters your freezer it will be put into the fill cup.
Read More At : www.doityourself.com...

Water leaking from ice maker into ice bin ...


Water leaking from ice maker into ice bin. Katerina S. • Jacksonville, FL • June 13, 2014. My Repair & Advice. It took me about 10 minutes to replace the ice ...
Read More At : www.appliancepartspros.com...

Ice maker leaking into cube bin - Appliance Repair Forum


Discuss Ice maker leaking into cube bin in Refrigerator & Freezer Repair. "When the water is filling the ice cube maker, there is a slight leak at the junction just ...
Read More At : forum.appliancepartspros.com...

Refrigerator's Ice Maker Leaking Water | ThriftyFun


This is a guide about refrigerator's ice maker leaking water. ... the ice maker leaks into the ice bin. I replaced the water valve with no luck.
Read More At : www.thriftyfun.com...

Icemaker leaking into ice bin - AppliancePartsPros.com


Icemaker leaking into ice bin. Alan D. • Lubbock, TX • January 23, 2017. Appliance: Model WRF535SMBM My Repair & Advice . Had to replace icemaker(third time in ...
Read More At : www.appliancepartspros.com...

Suggested Questions And Answer :


Ice maker leaks into the ice storage bin


Turn off the power to the appliance and apply a hairdryer to the ice maker compartment for about 2 mins , worked for me.
Read More At : Freezers...

Ice maker water leak in freezer. 8 yr old Amana std freezer on top, water actively leaking from ice maker into bin. Is it worth repairing?


Probably the solenoid (electric valve that opens and let the water from the supply line go into ice maker when It calls for it) is leaking and needs to be replaced ,it's not an expensive job. To make sure this is the problem ,shut of the ice maker by putting up the lever and wait a few hours and look inside the ice maker , if is water inside ,that's the problem ,if not the ice maker is the problem and has to be fix or replaced ; but is better to replace it ,won't be a big diference in cost.
Read More At : Freezers...

Hello, we have a 5 yr old Kenmore 73502 / 73504 / 73509 Bottom Freezer. Icemaker recently stopped making ice cubes. Instead what happens is: water just seems to pour through or over the cube maker, and fills the storage bin with water, which then freezes into a solid block. Occasionally there are a couple of misshapen cubes mixed in. I can hear the water dispenser turning on from time to time as it should. The freezer is definitely cold enough. Thanks. Dan


Behind the main drive gear is a copper plate. Near the end of the cycle that plate rubs against a probe and energises the water valve. The arcing cause that copper plate to stick to the probe for more than the alloted time (7.5secs) and this causes the water to overfill. I have a page with repair photos and a repair manual: HERE
Read More At : Freezers...

I have a Kenmore side/side with water dispenser and ice maker. Ice maker is not making ice, but I still get water. Every once in awhile I see a puddle under fridge (a large puddle). When I pull the fridge out from the wall I see a tube that runs from the water line up to the back of the ice maker. This tube is not connected to spout leading into the ice maker. I can also feel water on the back side of the fridge leading me to believe this is the source of my water leak. If water is going up there, I am not sure why it isn't going into the ice tray. And why the tube is comeing undone and water leaking everywhere. I though maybe ice was built up, but I defrosted and still have the issue.


Hi TJ,It'll cost around $65.00 to take care of this problem. The problem is the water inlet valve. The part number is 4389177 and can be picked up at your local appliance parts retailer or you can get one online maybe for a better price (just plug the part number into your favorite search engine).Here's what's happening... The valve I mentioned is actually a "dual coil" unit. One coil supplies the cold water, the other feeds the ice maker. These "coils" are independant of each other, so one coil can fail and the other can keep on truckin', no problem. But what you have is an Ice Maker coil/valve that is weak and it's allowing water to bypass.Basically the IM valve isn't closing shut completely. Imagine a dripping faucet... that's what it's like except you can't hear the drops, you can only see the results. Imagine drop by drop rising up that tube behind the fridge and into the IM. One drop at a time. These drops of water go into the freezer compartment through the IM fill tube. Now when these little ***** drops slide down the fill tube inside the freezer compartment they flash freeze before they reach the IM. One drop after another... drip drop drip drop. All these little droplets of water eventually form a glacier inside the fill tube. OK, now we're at the point of glatiation. The fill tube (just behind the ice maker) has completely frozen solid. Now... when the IM "calls" for water to refill itself, the (failed) valve opens up and lets full pressure through. But where is this water/pressure going to go? The pressure builds inside the 1/4" water line until it can't handle it any more, the pressure looks for the path of least resistance. That path is the connection that you found loose. It blew out because the fill tube (into the freezer) is blocked with ice and the reason it's blocked is because the valve isn't shutting off completely.That's alot of words to say this... it's an easy fix. Get the valve (above). Pull the fridge out. Unplug it. Turn the water off at the wall. Remove the water line going into the valve and set aside. Remove the cardboard panel. Remove the 2 screws holding the valve to the fridge. Pull the valve out. Note the electrical and tubing connections carefully. Get your new valve out and install the electrical and tubing just like the old one. Then rebuild, turn on the water and look for any leaks (use a flashlight and take a minute or two here... finding a leak now will save you alot of misery later). Replace the cardboard and plug it back in.There ya go! Your first major appliance repair job done successfully? Priceless.SG
Read More At : Freezer 20.3 cu. ft. Frost Free Upright Freezer...

The water that fills the ice maker overfilled one night and leaked water throughout the freezer and onto the floor. Eventually the water going into the freezer shut off. With the ice level too high, the ice maker could not eject the ice and became stuck. After cleaning out the ice from the ice maker, the system does not work. Water will not go into the ice maker.


First replace the water valve
Read More At : Whirlpool...

Mine is a 7 -8 year old separate Freezer with an "Electronic Ice Maker inside. It seems to overfill with water a small amount which overtime freezes all the cubes in the storage bin. Is there a way to adjust the amount of water per cycle?


None,this water cycle is controlled exclusively by the "mother-board/main-board in the lower rear area of the unit,the only other possibility would be is if the water solenoid valve isn't completely shutting off and letting water enter after a timed fill per the motherboards circuit timer or you are using the wrong ice cube tray(s) that may be of too small capacity,the boards new number is WR55X10942 made by G.E.Corp
Read More At : GE...

Tips for a great answer:

- Provide details, support with references or personal experience .
- If you need clarification, ask it in the comment box .
- It's 100% free, no registration required.
next Question || Previos Question
  • Start your question with What, Why, How, When, etc. and end with a "?"
  • Be clear and specific
  • Use proper spelling and grammar
all rights reserved to the respective owners || www.glacierfreezer.com || Terms of Use || Contact || Privacy Policy
Load time: 0.0728 seconds